Product Search

Search

Search the full site including products, accessories, news posts & pages.

Product Finder

Our Product Finder tool allows you to find the perfect product for your requirements.

Cleat Specification Tool

Helping you find the right cleat for your application.

EN-US EN-GB CN

Sovereign Extreme Heavy Duty Stainless Steel Hinged Cable Cleat

We'd like to keep in touch

We have some exciting things in the pipeline - if you'd like to be the first to know please enter your email address below.

Oops! We could not locate your form.

No thanks, I'd just like to Download the datasheet.

The Sovereign cable cleats are metallic cable cleats which have been designed, constructed, and tested in accordance with the International Standard ‘cable cleats for Electrical Installations’ IEC 61914. The Sovereign cable cleat has been designed and tested for high short circuit conditions on cables held in trefoil application / formation, to ensure the securing and retention of cables without damage.

The range is fabricated from 316L stainless steel, giving it high creep strength whilst providing excellent corrosion resistance in the harshest of environments. The Sovereign cable cleat is available for trefoil application/ formation for diameters of 17mm to 128mm in 24 sizes.

The cleat has one M12 and two M10 fixing clearance holes within its base, allowing versatility to the installer during installation, and is designed to enable the product to be secured to a variety of mounting surfaces. The hinge opens fully, allowing the cables to be easily placed within the cable cleat, to aid the installer before closing and securing via the mouth piece bolt.

Liners come as standard which help to restrain the cable(s) within vertical applications. Where thermal elongation of cables occurs, the liner also provides a layer of protection between the cable sheath and the cable cleat during normal operation. This additional layer protects the cable from chafing on any mounting surface due to differential movements such as those found in marine and offshore applications. The liners also assist in the extra protection of cable(s) in the event of short circuit fault conditions. The standard liners supplied are classified as Low Smoke & Fume (LSF), Zero Halogen (LS0H) and Phosphorus Free.

Features

  • Third party certification to IEC 61914
  • 316L stainless steel
  • 17 – 128mm in 24 sizes for trefoil formation /application
  • Short circuit rating of 190kA peak fault
  • Operating temperature -50°C to +60°C
  • Liners are classified as Low Smoke & Fume (LSF), Zero Halogen (LS0H) and Phosphorus Free
  • Combined single (M12) and two bolt (M10) fixing design

Patents granted: SG 11201506573Q, US 9551438

Short Circuit Testing to IEC 61914 - Clause 9.5
Trefoil Formation
One short circuit 300mm fixed cleat centres Two short circuits 300mm fixed cleat centres One short circuit 600mm fixed cleat centres Two short circuits 600mm fixed cleat centres
0.1 sec 1 sec 0.1 sec 1 sec
190kA Peak 96kA Peak 150kA Peak 80kA Peak
87.7kA RMS 46.1kA RMS 68.2 RMS 38.1kA RMS
300mm Sovereign HDSS (0.1 sec)
Cable OD (mm)Peak kA
36190.0
38195.2
43207.7
59243.2
65255.3
Type 6.1.3 Composite HDSS - Heavy Duty Stainless Steel
Design Specification IEC 61914
Temperature for permanent application -50°C to +60°C
IEC 61914 clause 6.2
Needle Flame Test Pass - 120 second flame application time
IEC 61914 clause 10.0, 10.1, IEC 60695-11-5
Lateral Load Test Refer to CMP Products, IEC 61914 clause 9.3
Axial Load Test 0.7kN, IEC 61914 clause 9.4
Impact Resistance Pass - Very heavy
IEC 61914 clause 6.3, 6.3.5, 9.2
Material 316L Stainless Steel with Standard Liner
Standard liners are classified as Low Smoke & Fume (LSF), Zero Halogen (LS0H) and Phosphorus Free
UL Certificate 20181221_E490770
UL Compliance Standards UL 2239, CSA C22.2 No. 18.4-15

Coatings are available upon request by adding the following suffixes to the ordering reference – EC for epoxy coating, PC for polyester coating and TC for thermoplastic coating. Example order reference for epoxy coating suffix EC (HDSS033038EC). Fasteners required to secure the cable cleat to the support structure are not included but can be supplied upon request. Isolation/separation pads (to prevent corrosion between two dissimilar metals) are not included but can be supplied on request - see isolation / seperation page.

Product Selection Table

Sovereign Part No.Cable Ø Range Take (in.)Dimensions (in.)Weight (oz)
WHDPFixing Hole Ø
D1D2
HDSS0170210.669 - 0.8263.8973.4642.1260.9842 x M10 1 x M1214.32
HDSS0190230.748 - 0.9063.9373.4252.1260.9842 x M101 x M1214.71
HDSS0230280.906 - 1.1024.0943.4652.1260.9842 x M101 x M1215.87
HDSS0270321.063 - 1.2604.1733.8192.1260.9842 x M101 x M1216.40
HDSS0300351.181 - 1.378 4.2524.0552.1260.9842 x M101 x M1216.68
HDSS0330381.299 - 1.4964.3314.2132.1260.9842 x M101 x M1217.11
HDSS0360421.417 - 1.6545.1974.2522.1261.9692 x M101 x M1220.11
HDSS0400461.575 - 1.8115.2764.4492.1261.9692 x M101 x M1220.49
HDSS0440501.732 - 1.9695.3544.7642.1261.9692 x M101 x M1220.95
HDSS0480551.890 - 2.1655.4335.0002.1261.9692 x M101 x M1221.73
HDSS0510582.008 - 2.2835.5125.1182.1262.9532 x M101 x M1222.12
HDSS0550622.165 - 2.4416.1815.4332.1262.9532 x M101 x M1224.83
HDSS0590662.323 - 2.5986.1815.7092.1262.9532 x M101 x M1225.33
HDSS0630702.480 - 2.7566.2995.9842.1262.9532 x M101 x M1225.86
HDSS0670742.638 - 2.9136.4176.2992.1262.9532 x M101 x M1226.38
HDSS0710782.795 - 3.0716.6146.5752.1262.9532 x M101 x M1226.95
HDSS0740822.913 - 3.2287.4806.8902.1262.9532 x M101 x M1230.44
HDSS0770853.031 - 3.3467.5597.0872.1262.9532 x M101 x M1230.79
HDSS0820883.228 - 3.4657.5987.3232.1262.9532 x M101 x M1231.15
HDSS0880963.465 - 3.7807.9537.9132.1262.9532 x M101 x M1232.24
HDSS0961033.780 - 4.0558.4258.4652.1262.9532 x M101 x M1233.23
HDSS1031114.055 - 4.3709.3319.0162.1262.9532 x M101 x M1237.21
HDSS1111194.370 - 4.6859.7649.6062.1262.9532 x M101 x M1238.31
HDSS1191284.685 - 5.03910.43310.2362.1262.9532 x M101 x M1239.58

Technical Illustration